All Case Studies
    Commercial Door Replacement · Case Study

    Three Hollow Metal Doors & Frames Replaced — Anaheim Hills, CA

    October 30, 2026 Anaheim Hills, CA Hollow Metal Door & Frame Replacement
    By InSev TechPublished
    3
    personnel doors & frames replaced
    Concrete-backfilled frames
    cut out and rebuilt
    1 door per visit
    facility stayed open throughout
    2
    rolling steel doors also corrected
    01

    The Problem

    Anaheim Hills, CA · pet care / daycare facility

    The facility's interior personnel doors had worn out, and the frames were not the usual anchor-mounted type. They were backfilled with solid concrete, so a simple door swap was not possible. Each opening needed demolition before the new frame could go in. The building is an active dog-care facility — animals and customers are on site throughout the day — so noise, dust and open doorways had to be kept to a minimum.

    02

    What We Found

    The old frames had rusted through at the base and hinges (see gallery), and because each frame was filled with concrete, there was nothing to unbolt and no sound frame to hang a new door on. The openings themselves were sound once the old units were out. The correct scope was full replacement of door and frame at all three openings — Toybox, Gym and Romper #1 — plus corrective repairs on two rolling steel doors: a bent guide and worn bottom seals.

    03

    What the Work Included

    This commercial door repair work included:

    1. Coordinated with office staff on arrival and secured the work area.
    2. Removed the existing hollow metal door from the opening.
    3. Cut the old frame out of the opening with a hand circular saw.
    4. Cleared remaining concrete with a chipping bit on a rotary hammer where the saw could not reach.
    5. Dry-fit the new frame. The opening was 1/16" short of the required width, so one side of the new frame was trimmed by 1/16" for a proper fit.
    6. Set and secured the new frame, then drilled and installed new 3/8" x 5" anchors.
    7. Caulked the full perimeter of the frame to close all gaps.
    8. Hung the new hollow metal door on new hinges.
    9. Installed the new mortise lock body.
    10. Transferred the customer's existing alarm magnet and lath guard to the new door so the alarm setup stayed in place.

    Materials installed (per door): 1 hollow metal door and matched frame (36" x 80"), 1 commercial mortise lock body, 3 commercial 4.5" hinges, 8 anchors 3/8" x 5", 4 tubes of caulk. Each new door was also fitted with lever hardware and a stainless steel kick plate.

    Rolling steel doors: on the same job, the crew corrected problems on two rolling steel doors, including a replacement guide and a new vinyl bulb bottom seal on the Toybox room door.

    04

    Straight Talk: Repair vs. Replace

    A door leaf can sometimes be swapped on a sound frame. These frames were not sound: rust had eaten through the base and hinge areas, and the concrete fill meant the frame could not be adjusted, re-anchored or patched back to strength. Patching rust-through is cosmetic — the frame keeps losing section where it carries the hinges. Once a frame is rusted through and grouted in place, replacement of the door and frame together is the only repair that lasts.

    05

    The Result

    • Three personnel openings rebuilt with new frames and doors, each tested and working before the crew left.
    • Every door cycled repeatedly and given a final check with office personnel; each opening returned to service the same day.
    • Work split into separate visits, one door per day, so the facility never lost more than one opening at a time — and stayed open throughout.
    • Both rolling steel doors corrected: guide replaced/straightened and new bottom seal fitted, travel and closure verified.
    07

    Project Gallery

    8 real field photos from this job — no customer name, address, or contact details in any photo or caption.

    Before: one of the original personnel doors, with peeling paint and rust at the frame base.
    Before: one of the original personnel doors, with peeling paint and rust at the frame base.
    Close-up: the bottom hinge and jamb had rusted through — the frames were beyond repair.
    Close-up: the bottom hinge and jamb had rusted through — the frames were beyond repair.
    Measuring the existing opening — the concrete-filled frame left no room for adjustment, so one side of the new frame was trimmed by 1/16" for a proper fit.
    Measuring the existing opening — the concrete-filled frame left no room for adjustment, so one side of the new frame was trimmed by 1/16" for a proper fit.
    The Toybox rolling steel door — worn bottom seal and guide before repair.
    The Toybox rolling steel door — worn bottom seal and guide before repair.
    Testing the repaired rolling steel door — smooth travel and full closure verified with the chain hoist.
    Testing the repaired rolling steel door — smooth travel and full closure verified with the chain hoist.
    Finished: Toybox room — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    Finished: Toybox room — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    Finished: Romper #1 — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    Finished: Romper #1 — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    Finished: Gym — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    Finished: Gym — new 36" x 80" hollow metal door and frame, lever hardware and stainless steel kick plate.
    08

    Frequently Asked Questions

    1. Can a hollow metal door be replaced without replacing the frame?

    If the frame is sound, yes. On this job the frames were rusted through and filled with concrete, so the door and frame had to be replaced together.

    2. What does it mean that a door frame is backfilled with concrete?

    The steel frame was filled with concrete when it was originally set. It cannot be unbolted or adjusted — removal means cutting the frame out and chipping away the remaining concrete before a new frame can be anchored in.

    3. How long does a door and frame replacement take?

    Each opening here was completed and returned to service the same day. Scheduling one door per visit kept the rest of the facility fully operational.

    4. Can the work be done while our facility stays open?

    Yes. The crew secured one work area at a time, coordinated with office staff at each arrival, and kept noise, dust and open doorways to a minimum — this facility stayed open throughout.

    5. When should a rusted door frame be replaced instead of repaired?

    When rust has eaten through the frame at the base or hinge areas. At that point the frame has lost the section that carries the door's weight, and patching does not restore its strength.

    Call 24/7 — (657) 377-0809